Vision 40W
Table des matières
Données techniques
- Type de laser
- co2
- Puissance de sortie
- 40 W
- Zone de travail
- 400 × 270 mm
- Vitesse
- 600 mm/s
- Type de connexion
- WIFIUSB
- Assistance d'air
- Pris en charge
- Caméra
- Pris en charge
- Caisson
- Pris en charge
- Poids
- 19.34 kg
- Garantie
- 12 mois
Matériaux : Découpe & Gravure
Découpe
- “ABS plastic”“plastic”3 mm“1 pass”Assistance d'air
“Melts and smokes” — “Emits hazardous fumes”
Sécurité:“Avoid—emits cyanide-containing fumes” • “cyanide gas - “Basswood”“wood”8 mm“1 pass”Assistance d'air★
“Minimal char” — “Soft wood cuts easily”
Sécurité:“Soft wood—monitor for flare-ups” • “smoke - “Birch plywood”“wood”6 mm“1 pass”Assistance d'air★
“Clean edge with air assist” — “Higher wattage gives less char”
Sécurité:“Use air assist; check for voids” • “smoke - “Cardstock (paper)”“paper”1 mm“1 pass”Assistance d'air★
“Crisp cut if fast” — “Use honeycomb and high air”
Sécurité:“Very flammable—use high speed” • “fire risk - “Cork”“other”5 mm“1 pass”Assistance d'air★
“Very clean if fast” — “Watch for flare ups”
Sécurité:“Cuts easily—very flammable” • “fire risk - “Corrugated cardboard”“cardboard”5 mm“1 pass”Assistance d'air★
“Clean if fast” — “Watch for flare in voids”
Sécurité:“Monitor constantly—can ignite” • “fire risk - “Cotton fabric”“fabric”2 mm“1 pass”Assistance d'air★
“Neat edge if fast” — “Laser cauterizes edge slightly”
Sécurité:“Very flammable—keep speed high” • “fire risk - “Delrin (acetal)”“plastic”6 mm“1 pass”Assistance d'air★
“Clean kerf” — “Invisible flame possible - monitor closely”
Sécurité:“Cuts well—strong odor; ventilate” • “formaldehyde fumes - “Denim (cotton)”“fabric”2 mm“1 pass”Assistance d'air★
“Clean cut” — “Minimal fray due to heat seal”
Sécurité:“Thick cotton—watch for ignition” • “fire risk - “EVA foam”“plastic”10 mm“1 pass”Assistance d'air★
“Minimal char” — “Good for cosplay patterns”
Sécurité:“Chlorine-free; ventilate for VOCs” • “acrid fumes - “Extruded acrylic”“acrylic”8 mm“1 pass”Assistance d'air★
“Clear edge prone to melt” — “Use higher speed to reduce melt”
Sécurité:“Melts easily—optimize speed/air” • “acrylic fumes - “Felt (wool)”“fabric”5 mm“1 pass”Assistance d'air★
“Clean cut on wool felt” — “Prefer natural wool felt”
Sécurité:“Prefer wool; avoid synthetics melting” • “smoke - “Leather (Chrome-tanned)”“leather”””
“Do not laser chrome tanned leather” — “Toxic gases from chromium salts”
Sécurité:“DO NOT LASER—toxic chromium gases” • “cyanide gas - “Leather (Vegetable-tanned)”“leather”3 mm“1 pass”Assistance d'air★
“Slight edge darkening” — “Odor present after cut”
Sécurité:“Ventilate—burnt hair odor” • “smoke - “PETG plastic”“plastic”6 mm“1 pass”Assistance d'air★
“Stringy edge” — “Use high air to cool cut”
Sécurité:“Tends to melt—ensure ventilation” • “acrid fumes - “Polycarbonate (PC)”“plastic”3 mm“1 pass”Assistance d'air
“Poor quality due to melt” — “Not recommended for cutting”
Sécurité:“Poor cuts—melts/chars; avoid” • “toxic fumes - “PVC (Polyvinyl Chloride)”“plastic”””
“Never laser PVC” — “Releases chlorine gas and acid vapor”
Sécurité:“NEVER LASER—releases chlorine gas” • “chlorine gas - “Rubber (laser-safe)”“other”6 mm“1 pass”Assistance d'air★
“Heavy soot - clean after” — “Ventilate and clean optics”
Sécurité:“Use only laser-safe rubber; ventilate” • “heavy soot
Gravure
- “Anodized aluminum”“metal”“1 pass”★
“Removes anodized layer” — “Exposes silver metal beneath”
Sécurité:“Safe to mark—coating absorbs beam” • “fine dust” - “Basswood”“wood”“1 pass”Assistance d'air★
“Good contrast on light wood” — “Defocus slightly for smooth shading”
Sécurité:“Soft wood—monitor for flare-ups” • “smoke - “Birch plywood”“wood”“1 pass”Assistance d'air★
“High contrast burn” — “Mask to reduce soot”
Sécurité:“Use air assist; check for voids” • “smoke - “Cardstock (paper)”“paper”“1 pass”Assistance d'air★
“Light score for folds” — “Reduce power to avoid cut through”
Sécurité:“Very flammable—use high speed” • “fire risk - “Cast acrylic”“acrylic”“1 pass”Assistance d'air★
“Frosty white” — “Focus slightly high for smoothness”
Sécurité:“Highly flammable—ensure ventilation” • “irritant fumes - “Cork”“other”“1 pass”Assistance d'air★
“Dark burn for graphics” — “Use low power for detail”
Sécurité:“Cuts easily—very flammable” • “fire risk - “Corrugated cardboard”“cardboard”“1 pass”Assistance d'air★
“Good for fold lines” — “Reduce power to avoid blowouts”
Sécurité:“Monitor constantly—can ignite” • “fire risk - “Delrin (acetal)”“plastic”“2 passes”Assistance d'air★
“Deep engrave possible” — “Good for stamp masters”
Sécurité:“Cuts well—strong odor; ventilate” • “formaldehyde fumes - “Denim (cotton)”“fabric”“1 pass”Assistance d'air★
“Dye bleaching effect” — “Defocus slightly for smooth fade”
Sécurité:“Thick cotton—watch for ignition” • “fire risk - “EVA foam”“plastic”“1 pass”Assistance d'air★
“Shallow texture” — “Useful for surface patterns”
Sécurité:“Chlorine-free; ventilate for VOCs” • “acrid fumes - “Extruded acrylic”“acrylic”“1 pass”Assistance d'air★
“Lower contrast than cast” — “Engrave appears clearer”
Sécurité:“Melts easily—optimize speed/air” • “acrylic fumes - “Glass”“glass”“1 pass”★
“Matte frost” — “Use wet paper to reduce chips”
Sécurité:“Engrave only; cannot cut” • “glass dust - “Leather (Chrome-tanned)”“leather”””
“Do not laser chrome tanned leather” — “Health hazard and machine corrosion”
Sécurité:“DO NOT LASER—toxic chromium gases” • “cyanide gas - “Leather (Vegetable-tanned)”“leather”“1 pass”Assistance d'air★
“Brand like mark” — “Masking reduces soot”
Sécurité:“Ventilate—burnt hair odor” • “smoke - “MDF”“wood”“1 pass”Assistance d'air★
“Dark engrave” — “Strong ventilation needed”
Sécurité:“Contains resin—use strong ventilation” • “formaldehyde fumes - “PETG plastic”“plastic”“1 pass”Assistance d'air★
“Low contrast” — “Prefer printing then cutting outline”
Sécurité:“Tends to melt—ensure ventilation” • “acrid fumes - “Polycarbonate (PC)”“plastic”“1 pass”Assistance d'air
“Low contrast engrave” — “Melts and discolors easily”
Sécurité:“Poor cuts—melts/chars; avoid” • “toxic fumes - “PVC (Polyvinyl Chloride)”“plastic”””
“Never laser PVC” — “Corrodes optics and mechanics”
Sécurité:“NEVER LASER—releases chlorine gas” • “chlorine gas - “Rubber (laser-safe)”“other”“2-3 passes”Assistance d'air★
“Deep relief for stamps” — “Allow cool down between passes”
Sécurité:“Use only laser-safe rubber; ventilate” • “heavy soot - “Slate (stone)”“stone”“1 pass”★
“Light gray contrast” — “Clean dust after job”
Sécurité:“Engrave only; dust control recommended” • “stone dust (silica)” - “Stainless steel”“metal”“1 pass”★
“Black mark with spray” — “Requires metal marking compound”
Sécurité:“Use marking spray with CO2; fiber ideal” • “metal fumes (chromium